Register / Login - Contact Info 

CAREER OPPORTUNITY AT TANDEMLOC: Mechanical Engineer, preferably with experience in the design of below the hook lifting devices.   Please send resumes to Tandemloc, 824 Highway 101, Havelock, NC 28532, attention Sandy Allen or sandy@tandemloc.com.

Custom Spreader Bars without the
custom price and without the custom lead time!
TANDEMLOC SPREADER BAR KITS
AC22P "SPREADER PIPE" Specifications and Drawings
Standard Spreader Pipe for use with AC25C End Caps


This item may be available for rental. Click for more information about renting this and other Tandemloc equipment.

This table shows different diameters, lengths and capacities for pipe, which can be used with Spreader Bar End Cap Kits and Connection Sleeves. Use this chart to purchase pipe “locally” or from TANDEMLOC, Inc.
  • WORK LOAD LIMIT (WLL): See table below
  • NOT PROOF TESTED, See Certification Note Below
  • CALCULATED WEIGHT: See table below
  • FINISH: Painted safety yellow.
• Standard specification #EAD21000A Applies
• NOTE 1: Material for all except "L" low temp arctic parts. (note 5) ASTM A500 GR B steel as standard but may be substituted with ASTM A53 GR B steel pipe or any structural pipe rated at 35,000 psi or greater, painted safety yellow. For "L" parts arctic low temp parts use ASTM A333/333M Grade 6 or 7 steel with certified charpy at -50° F. Painted Safety yellow with low temperature paint.
•
NOTE 2: Marking (Tandemloc supplied pipes)
SERIAL NO. (If proof tested) - Metal stamp in designated location.
VINYL DECAL - 2 Side, 3" Red; "NPS**. on AC25L label as noted and Tandemloc logo (red) or customer logo if spec.
**From chart w/ engineering approval
• NOTE 3: The holes that are drilled on each end must be on the same plane, within 1 degree. Holes are to be aligned for the mating end eye cap holes and allow passage of the safety pin. (Also see note 6.)
• NOTE 4: CERTIFICATION NOTE: TANDEMLOC supplied spreader pipes are certified to the material specification & test report received from the pipe producer and for the work load limit noted in the adjacent chart when used with suitably strong end caps and conforming to the lift angles noted on this drawing and the end caps. The pipe producer's material test report is attached to the TANDEMLOC certification.
• NOTE 5: Use temperature is 180°F to 25°F (per ASME B31.3) for standard part numbers.
  • NOTE 6: In some cases, earlier models of pipe caps had pin holes in different locations than on later models. A second set of pin holes may be drilled rotated 90° from the other set of holes. Pipes can then be used with both earlier and later end caps without affecting the strength ratings.
Product Photo
Download / view printer friendly data sheet(s)
Login / register to activate:
TANDEMLOC_AC22P.pdf
Type: Adobe Acrobat Document
Size: 74 KB
Need Credit? Let us know.
(Note: Credit Applications will only be processed with an accompanying purchase order.)


USE THE INFORMATION CONTAINED ON THIS PAGE WHEN SUPPLYING YOUR OWN PIPE




METHOD OF ORDERING (SEE NOTES 1 & 5 ON PAGE 1):
ORDERING EACH FINISHED SPREADER PIPE REQUIRES AN ORDER NUMBER WHICH DEFINES THE ACTUAL CUT LENGTH OF EACH SPREADER PIPE AS THE QUANTITY IN INCHES.
AN EXAMPLE FOR STANDARD STEEL FOLLOWS:
115” AC22P-03X-013 PIPE, 3”NPS/80/EH COMPONENTS, LENGTH BASED

AN EXAMPLE FOR ARCTIC STEEL FOLLOWS:
115” AC22P-03X-013L PIPE, ARCTIC 3”NPS/80/EH COMPONENTS, LENGTH BASED

*- Determine cut length by deducting "C" dimension from required span.
**- The Work Load Limits are for the assemblies shown in the diagram above. Note that the Work Load Limit is 2X the end cap individual rating because two end caps are used for a spreader.
LG. BASED ORD#
(See Above Image)		 SPREADER
PIPE SIZE		 O.D. I.D. C* A B WLL FOR
ASSEMBLED
SPREADER		 MAX SPAN AT STATE
 WLL & LIFT ANGLE		 CUT PIPE
WEIGHT
LB./IN.		 For custom configurations,
pricing, design  and delivery
schedules - any questions at all.
45° 60° 70°
AC22P-03X-007 3"NPS 80/EH 3.500±.035
2.90 +.111
-.035
13.50 2.00 1.00 28,000 LB. 11' - 0" 15' - 0" - 0.854
AC22P-03X-013 3"NPS 80/EH 3.500±.035
2.90 +.111
-.035
17.00 2.00 1.00 52,000 LB. 5' - 0" 11' - 0" - 0.854
AC22P-04X-013 4"NPS 80/EH 4.500±.045
3.83 +.129
-.045
18.00 2.00 1.00 52,000 LB. 12' - 0" 17' - 0" - 1.248
AC22P-05X-013 5"NPS 80/EH 5.563±.056
4.81 +.206
-.056
19.50 2.00 1.00 52,000 LB. 20' - 0" 27' - 0" - 1.732
AC22P-06X-013 6"NPS 80/EH 6.625±.066
5.76 +.174
-.066
20.50 2.00 1.00 52,000 LB. 27' - 0" 35' - 0"   2.381
AC22P-04X-025 4"NPS 80/EH 4.500±.045
3.83 +.129
-.045
25.94 2.00 1.00 100,000 LB. - 11' - 0" - 1.248
AC22P-05X-025 5"NPS 80/EH 5.563±.056
4.81 +.206
-.056
26.94 2.00 1.00 100,000 LB. 8' - 0" 18' - 0" - 1.732
AC22P-06X-025 6"NPS 80/EH 6.625±.066
5.76 +.174
-.066
28.85 2.00 1.00 100,000 LB. 18' - 0" 26' - 0" - 2.381
AC22P-08X-025 8"NPS 80/EH 8.625±.086
7.63 +.212
-.086
30.86 2.00 1.00 100,000 LB. 31' - 6" 42' - 0" - 3.616
AC22P-06X-045 6"NPS 80/EH 6.625±.066
5.76 +.174
-.066
29.50 2.00 1.00 180,000 LB. - 16' - 0" - 2.381
AC22P-08X-045 8"NPS 80/EH 8.625±.086
7.63 +.212
-.086
34.72 2.00 1.00 180,000 LB. 18' - 0" 31' - 0" - 3.616
AC22P-10X-045 10"NPS 60/EH 10.75±.108
9.75 +.234
-.108
37.00 2.00 1.00 180,000 LB. 31' - 0" 41' - 6" - 4.562
AC22P-10X-065 10"NPS 60/EH 10.75±.108
9.75 +.234
-.108
42.40 2.00 1.00 260,000 LB. 18' - 0" 36' - 0" - 4.562
AC22P-12X-065 12"NPS EH 12.75±.128
11.75 +.254
-.128
45.50 4.00 1.56 260,000 LB. 30' - 0" 47' - 0" - 6.097
AC22P-14X-085 14"NPS EH 14.00±.140
13.00 +.266
-.140
41.50 4.00 1.56 340,000 LB. - 45' - 0" - 7.058
AC22P-26X-250 26" EH 26.00±.260
25.00 +.386
-.260
50.00 6.00 2.00 1,000,000 LB. - 66'-0" - 11.350
AC22P-32X-552 32" EH 32.00±.320
31.00 +.446
-.320
70.50 7.00 2.00 2,208,000 LB. - 66'-0" 79' - 0" 14.017

Call Toll-Free: 1-800-258-7324 • Toll-Free Fax: 1-800-892-3273 • info@tandemloc.com • Site Map • Contact Us



TANDEMLOC, Inc · 824 Highway 101 · Havelock, NC 28532 USA · Legal Information

This  website contains the proprietary information of Tandemloc, Inc. and its affiliates and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.  You shall not, and shall not encourage, assist, or authorize another party to copy, distribute, publically display, modify, reverse engineer, decompile, or take any other action to reproduce or replicate any aspect of this Website or the information contained herein.

TANDEMLOC™, TANDEMLOC® logo, and TANDEMLOC AUTOLOC® are the trademarks of Tandemloc, Inc. Any unauthorized use of these or other Tandemloc, Inc. trademarks is prohibited.

© 2012 Tandemloc, Inc.  All rights reserved.

Products include lifting, mobilizing and securing products for below the hook and ISO container handling. Tandemloc provides standard corner fittings, lift beams, spreader bars, pipe end caps, container lifting devices, lifting attachments, twistlocks, d-rings, heavy duty casters, container casters, container lifting dollies and more.

Tandemloc, Inc., this website, and the products and services depicted herein are not affiliated or associated with Radford Brothers Industry, Jobsite Express, or Government Industrial Supply, and Tandemloc hereby expressly disclaims any affiliation, association, or endorsement that may be falsely implied by such entities.

Designed and deployed by Industrial Advertising · Links Page